Planetary Gear Motor - Off Topic Forum. - Country...
Please login or register free to be able to post.
View forum:
Planetary Gear Motor
Started by
Terry M. Bloom,
2022/06/14 10:35PM
Latest post: 2022/06/14 10:35PM, Views: 80, Posts: 1
Latest post: 2022/06/14 10:35PM, Views: 80, Posts: 1
Terry M. Bloom
Stepper motor with low speed, constant speed and large torque is applied to the characteristics of various kinds of driving devices. General component is common stepper motor hybrid stepping motor, permanent magnet stepper motor and reactive stepper motor. Among them, should be used in hybrid stepping motor.
The static torque of stepping motor itself several times higher than the same volume of brushless motor. But in some special occasions, as a result of the limitation of volume is empty, the output torque can not meet the requirements, you need to match the reducer. Because stepping motor itself did not run under the speed, so wear these with speed low speed reducer. Especially suitable for the position control, low working speed, constant speed control, small size, large torque, low noise, long working hours. Stepper motor is widely used in micro drive gearbox system, such as smart mobile phones lift cameras, camera, consumer electronics, intelligent driving equipment, intelligent medical equipment, etc.
Motor stepper Angle depends on the [url=https://www.ichgearmotor.com/planetary-gear-motor/low-speed-gear-motor/12-v... Gear Motor accuracy requirement of the load, which means the small resolution (equivalent) load conversion to the motor shaft, each equivalent motor to take how much Angle (including speed). Step motor of pitch Angle should be equal to or less than the Angle. Step currently on the market from the Angle of generally speaking, there are 0.6, 0.9, 1.2, 1.8, etc.
It is difficult to determine at dynamic torque of gear [url=https://www.ichgearmotor.com/planetary-gear-motor/low-speed-gear-motor/24-v... Gear Motor[/url] reducer, so we usually make sure the static torque of motor. The choice of the static torque based on the workload of the machine. The load can be divided into inertia load and friction load. Single inertial load, and there is no single friction load. Two kinds of load in qidong should consider directly (generally start from low speed), speed up the start to consider the inertial load, constant speed movement only considering the friction load. In general, the static torque should be 2 ~ 3 times of friction load. Once the static torque is selected, and base of the motor can determine length (geometry).
The same static torque of the motor, due to current parameters is different, have different operating characteristics. Of the motor current () refers to the driving power and the driving voltage can be judged based on the torque-speed characteristic curve.
The static torque of stepping motor itself several times higher than the same volume of brushless motor. But in some special occasions, as a result of the limitation of volume is empty, the output torque can not meet the requirements, you need to match the reducer. Because stepping motor itself did not run under the speed, so wear these with speed low speed reducer. Especially suitable for the position control, low working speed, constant speed control, small size, large torque, low noise, long working hours. Stepper motor is widely used in micro drive gearbox system, such as smart mobile phones lift cameras, camera, consumer electronics, intelligent driving equipment, intelligent medical equipment, etc.
Motor stepper Angle depends on the [url=https://www.ichgearmotor.com/planetary-gear-motor/low-speed-gear-motor/12-v... Gear Motor accuracy requirement of the load, which means the small resolution (equivalent) load conversion to the motor shaft, each equivalent motor to take how much Angle (including speed). Step motor of pitch Angle should be equal to or less than the Angle. Step currently on the market from the Angle of generally speaking, there are 0.6, 0.9, 1.2, 1.8, etc.
It is difficult to determine at dynamic torque of gear [url=https://www.ichgearmotor.com/planetary-gear-motor/low-speed-gear-motor/24-v... Gear Motor[/url] reducer, so we usually make sure the static torque of motor. The choice of the static torque based on the workload of the machine. The load can be divided into inertia load and friction load. Single inertial load, and there is no single friction load. Two kinds of load in qidong should consider directly (generally start from low speed), speed up the start to consider the inertial load, constant speed movement only considering the friction load. In general, the static torque should be 2 ~ 3 times of friction load. Once the static torque is selected, and base of the motor can determine length (geometry).
The same static torque of the motor, due to current parameters is different, have different operating characteristics. Of the motor current () refers to the driving power and the driving voltage can be judged based on the torque-speed characteristic curve.
Please login or register free to be able to post.
- Links allowed: yes
- Allow HTML: no
- Allow BB code yes
- Allow youTube.com: yes
- Allow code: yes
- Links visible: no
- Quick reply: yes
- Post preview: yes